You're currently in Business Support. For help with a consumer service, visit our

newNotificationBanner

AlarmForce equipment

Change the batteries in your AlarmForce equipment

Alarm Force

## Legacy panel

1. Turn off and disconnect the power for the panel
2. Remove the panel lid to the battery
3. Remove the used lead-acid battery by detaching the white clip. Connect the new lead-acid battery using the same white clip
4. Insert a new 12V Lead Acid battery into the panel. Put the excess wires to the side of the battery into the panel. Put the excess wires to the side of the battery
5. Re-attach the panel lid
6. Turn the panel back on
7. Test whether the replacement is successful by arming and disarming the panel. If the panel no longer says "low system battery," the replacement is successful
8. Please dispose of the used lead-acid battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business AlarmForce legacy panel from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/en/business/support).

[youtube:id:f6fD58Jylj8]

## Wireless carbon monoxide alarm 80 AF

1. Remove the CO detector from mounting plate by twisting it counter clockwise to unlock
2. Open the cover
3. Insert a new CR123 battery into the device
4. Close the cover
5. Twist the CO detector clockwise to lock onto the mounting plate
6. Please dispose of the used battery by contacting your local battery recycling programs

## Door/window sensor 31AF

1.	Remove your sensor and remove the case by twisting a small flat blade screwdriver in the top case slot (on the flat end of the sensor)
2.	Remove the battery retaining screw
3.	Remove the battery clamp and original batteries from the device
4.	Replace with two new lithium batteries with the “+” side up
    - If you see a white ring around the batteries, you need two CR2032 lithium batteries
    - If you do not see a white ring around the batteries, you need two CR2450 lithium batteries
6.	Replace the battery clamp and retaining screw
7.	Replace the case back onto the sensor 
8.	Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business AlarmForce door/window sensor from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/en/business/support).

[youtube:id:L32I1JhXHTg]

## Door/window sensor 36AF

1. Remove your sensor and use a small flat blade screwdriver or coin in the slot on either end of the transmitter
2. Slide the original battery out of the device
3. Replace with a new CR2450 lithium battery
4. Close the lid back onto the sensor
5. Please dispose of the used battery by contacting your local battery recycling programs

## Glass break detector 91AF

1. Open your Glass Break Detector sensor case
2. Remove the battery clip screw and move clip to the side to access the batteries
3. Install two CR2450 lithium batteries with the “+” side up
4. Put back the battery clip screw and movie clip to their original location
5. Close the sensor case
6. Please dispose of the used battery by contacting your local battery recycling programs

## Key fob MKA-315

1. Use a small Phillips screwdriver to open the back cover of the key fob
2. Slide out the CR2032 battery and replace with a fresh battery
3. Secure the back cover by using the two Phillips screws
4. Please dispose of the used battery by contacting your local battery recycling programs

## Key fob RC7

1. Remove the battery cover of the key fob by using a coin to turn counter-clockwise
2. Insert a new CR2032 battery into the key fob with the unmarked side (negative) of the battery facing down
3. Replace the battery cover by securing the cover using a coin to turn clockwise
4. Please dispose of the used battery by contacting your local battery recycling programs

## Wireless motion detector 54AF

1. Remove the screw at the bottom of the device (if any) and open the case
2. Replace the original battery in the device by connecting a 9V battery to the battery clip (“+” side up)
3. Replace the case screw after closing the case
4. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business AlarmForce wirless motion detector from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/en/business/support).

[youtube:id:_QNqioTwtkw]

## Wireless motion detector 55AF

1. Squeeze the top and bottom of the case to open the motion detector
2. Replace the CR123A battery in the device. Make sure to take note of the battery polarity
3. Return the sensor to its bracket and snap the case close
4. Please dispose of the used battery by contacting your local battery recycling programs

## Remote keypad KP7

1. Remove the cover by loosening the screw at the bottom of the device
2. Replace the 3 AAA batteries within the keypad
3. Replace the cover and tighten the screws
4. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business AlarmForce remote keypad from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/en/business/support).

[youtube:id:J0uuNiImpSs]

## Wireless smoke alarm 72AF

1. Remove the smoke alarm from mounting plate by twisting it counter clockwise to unlock
2. Open the cover
3. Insert the two 9V batteries into the device
4. Close the cover
5. Match up the alignment tabs and twist the smoke detector clockwise to lock onto the mounting plate
6. Please dispose of the used battery by contacting your local battery recycling programs

## Wireless smoke alarm 73AF

1. Remove the smoke alarm from mounting plate by twisting it counter clockwise to unlock
2. Open the cover
3. Insert the CR123 battery into the device
4. Close the cover
5. Twist the smoke detector clockwise to lock onto the mounting plate
6. Please dispose of the used battery by contacting your local battery recycling programs

## Wireless keypad 10AF

1. Remove the top of the case by twisting a small screwdriver between the case halves until it pops open
2. Remove the original battery from the battery clip
3. Replace and connect the new 9V battery to the battery clip
4. Close the case back
5. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business AlarmForce wireless keypad from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/en/business/support).

[youtube:id:UhMSUI-TXqE]

 AlarmForce equipment Swiftype Title

Learn how to change the batteries in your AlarmForce equipment, including garage door lock, glass break detector and other SmartHome Security devices.

AlarmForce equipment Swiftype Description

AlarmForce equipment / SEO

Change batteries in Alarmforce equipment | SmartHome | TELUS Support

2GIG equipment

## Wireless thin door/window sensor

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/2xG5cpVjQjMqUeABGPYxnl/1e83a3e0ccc34849e2daba8acddb091a/2GIG_Wireless_Thin_Door_Window_Sensor__2GIG-DW10-345_.png">

1. Make sure the system is disarmed
2. To remove the sensor cover, use your finger to press the tab on the end of the case. This disengages the clip holding the cover to the base
3. Place a small flathead screwdriver in the slot between the metal clip and battery and twist the screwdriver slightly while holding back one of the black plastic edges holding the battery
4. Insert two new CR2032 lithium coin batteries with the plus (+) sign facing up
5. Verify programming and RF communication with the Control Panel
6. Dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG wireless door/window sensor from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:MkpP26v57aQ]

## 4 button key ring remote

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/5IzUbZi3NKg8r2Y77cMlII/6719a0fb39e15141739600126f4b7f95/4_Button_Key_Ring_Remote__2GIG-KEY2-345__.png">

1. Before changing the batteries, make sure your system is disarmed
2. Use a precision Phillips head screwdriver to unscrew the only screw where we have the key ring and remove the back plate
3. Remove the old battery by gently sliding out of it’s tray
4. Insert the replacement CR2025 3V lithium coin battery. The (+) sign on the battery should be facing up
5. Replace the back plate and screw it back in place
6. Test whether your replacement is successful by pressing and holding the unlock button. If the LED lights up RED, the batteries are properly installed
7. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG 4 button key ring remote from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:suYy4wNW6xA]

## CO detector

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/3znULaqRE0K6NELF2AT2Hj/03d7f3635c8902922fac2b6182563c9a/CO_Detector__2GIG-CO3-345__.png">

1. Remove the detector from its mounting base by twisting the detector counterclockwise
2. Remove the old battery. To ensure proper power-down sequence, wait a minimum of 20 seconds before installing the new battery
3. Install a new 3-volt CR123A Lithium battery. Follow the polarity diagram inside the compartment. If the battery is incorrectly inserted, remove gently with a non-conductive tool and correctly reinsert
4. Reinstall onto the mounting base by turning the detector clockwise
5. After the power-up sequence, the green LED should blink about once every 12 seconds to indicate normal operations. If the battery is not installed correctly, the detector will not operate and the battery may be damaged
6. Please dispose the used batteries by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG CO detector from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:-CyecfWNlF0]

## Flood detector

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/1GEq8IdaK51WtfxNOmOfvA/98870a9f05507632645325282b889387/Flood_detector.png">

1. Make sure the system is disarmed and go to installer menu of the panel (in some panels this sensor is programmed for 24 hours and tampering the sensor can trigger an alarm)
2. Open and separate the sensor case
3. Remove the battery. Wait two (2) seconds
4. Replace the battery using a new CR2 lithium battery. Close sensor
5. Wait one minute and then you can exit the installer menu
6. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG flood detector. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:k27TFXRfBbY]

## Glass break detector

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/vxajwsPjtmZV4CizPEnxG/c977ea1362e367ba74b0b36cd431b34b/2GIG_Glass_Break_Detector__2GIG_GB1_345__.png">

1. Make sure the system is disarmed and go to installer menu of the panel (in some panels this sensor is programmed for 24 hours and tampering the sensor can trigger an alarm)
2. Remove the cover from the base by twisting it counterclockwise
3. Replace with two CR123A lithium batteries and twist back the sensor on the backplate
4. Please take note of the polarity of the battery. Improper handling of lithium batteries may result in heat generation, explosion or fire, which may lead to personal injuries
5. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG glass break detector from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:hBst1ER-myc]

## Motion sensor

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/6BsfX3t2rQXjQaxMugizES/d0be28a8ac1bb62f0c8e02b1ea3dbf38/Motion_sensor_.png">

1. Make sure your system is disarmed
2. Press the tab at the top of the sensor and pull open the back removing the front piece off of the back mounting plate
3. Remove the CR123A 3V lithium battery
4. Slide in the new CR123A 3V lithium battery and align it with the polarity on the sensor
5. Attach the hinges back
6. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business Honeywell motion sensor from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:uLAO4_AOLQE]

## Smoke sensor

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/7xH9Enk1S69YiYk0fzL7eB/b297a5803abb182b2ff0cbb137940c03/Smoke_sensor_.png">

1. Remove the smoke alarm from its mounting base by twisting the smoke alarm counterclockwise
2. Remove the old battery and to ensure proper power-down sequence, wait a minimum of 20 seconds before installing new batteries
3. Insert a new CR123A 3V lithium battery in the battery compartment. Follow the polarity diagram inside the compartment
4. Reinstall the smoke alarm onto the mounting base by turning the smoke alarm clockwise
5. Please dispose the used batteries by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business Honeywell smoke sensor from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:JUUZJTB-4Y8]

## Panic button remote

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/3pmQWJDazBoE5aglkN1SQf/8858eb4b6a0b020782a66e4a83a42a1f/Panic_button_remote_.png">

1. To avoid any panic signals during the battery replacement process, make sure your system is disarmed. 
2. Insert a small, flathead screwdriver into the opening on the panic button. Then remove the top cover
3. Gently insert the flathead screwdriver between the battery and one of the metal clips in the battery compartment. Then remove the old battery
4. Insert the replacement CR2032 lithium battery with the positive (+) sign facing up
5. If you remove the circuit board (not recommended), ensure the LED aligns with the appropriate hole on the top cover
6. Verify that the panic button is programmed into the control panel and ensure that it has quality radio frequency (RF) communications with the panel
7. Replace the panic button top cover
8. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG panic button remote from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:MLCHdcCc6dA]

## Secondary analog keypad

<img width="300" max-width="300" src="//images.ctfassets.net/9mt4r6ro1ay9/2IdYxSYSca1xGZVYyyoUsq/84e6eee97241454bf877057ae7585971/Secondary_Analog_Keypad__2GIG-PAD1-345_.png">

1. Press the hinged tabs on top of the keypad to separate the mounting plate from the unit
2. Place a small flathead screwdriver in the slot between the metal clip and the battery
3. Twist the screwdriver slightly while holding the black plastic edges holding the battery
4. Insert the two replacement CR2032 lithium batteries in the compartment. The plus (+) sign of both batteries should be facing up and the minus (-) side facing down
5. Ensure that the programming settings are correct
6. Please dispose of the used battery by contacting your local battery recycling programs

Learn how to replace the battery of your TELUS Secure Business 2GIG secondary analog keypad from your phone. Do it yourself by watching the brief video. For more information on managing your TELUS Secure Business, visit [__telus.com/en/business/support__](https://www.telus.com/business/support).

[youtube:id:rx2AcNlBsq4]

## Control panel

<img width="300" max-width="300" src="//images.contentful.com/qtoioov2cmu7/7meDaUVEO03fKp2hXmApwf/0701680c78e31cc2e046e4f0f51bbd5d/2GIG_-_Control_Panel.jpg">

1. Before you begin, disarm and power down your panel
2. Locate and remove the screw on the top of the keypad
3. Gently pull down the front cover down. Do not let go of the cover when removing the front from the panel 
4. Locate the third hand (a plastic piece resembling an upside down “V”) and place it over the notch in the centre of the cover. This will allow the front cover to gently hold onto the panel
5. Locate the green battery pack and remove the clip that connects the battery’s red and black wire to the circuit board
6. Remove the original battery. You may use your flathead screwdriver to gently remove the battery from its place
7. Insert the new 2GIG panel battery and plug back in the clip
8. Unhook the third hand and close the cover. Press the cover to the panel shut until it snaps into place
9. Replace the screws at the top of the keypad and let panel charge for 24 hours

__Tools required__: A small to medium flathead screwdriver.

2GIG equipment / SEO

Get instructions on how to change the batteries in your 2GIG equipment, including smoke sensor, CO detector and other Secure Business devices.

2GIG equipment battery replacement | Support | TELUS Business

Change the batteries in your 2GIG equipment

2GIG

[img src="//images.ctfassets.net/9mt4r6ro1ay9/5Anaj163xaFLJRd1qNkcwT/7f5cfae588c0a6e61074c5bc0a808522/4-button_key_fob.png" alt="4-button key fob." max-width="230"]

[youtube:id:i_-4aevui3c]

Before you start, you will need:

- A new CR2032 Battery (purchased online or through a local retailer)
- Phillips head screwdriver

To replace the batteries for your 4-button keyring remote, please follow the instructions below:

1. Make sure the system is disarmed. To avoid sending any accidental panic signals, put the key fob down on a flat surface.
2. Remove the backside screw and open the cover using a screwdriver.
3. Push out the original battery from its holder.
4. Insert the new CR2032 with the polarity “+” on top.
5. Test the unit by momentarily pressing on the Transmit buttons - the LED should light up.
6. Replace the cover and attach it with the screw and screwdriver.
7. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / 4-button key fob

[img src="//images.ctfassets.net/9mt4r6ro1ay9/67I9YxG4YFbOWa6PhcjocQ/c9803121a2e9686e8ef1aca49b936d42/Door___window_security_contact__PG9975__.png" alt="Door & window security contact (PG9975)." max-width="250"]

[youtube:id:9EHas-2Uwww]

Before you start, you will need:

- One new CR2032 battery (purchased online or from a local retailer)
- 4mm flat-head screwdriver

To replace the batteries for your Door & window security contact (PG9975), please follow the instructions below:

1. Make sure the system is disarmed and remove the device from its original position.
2. Insert a 4 mm flat screwdriver into the slot of the plastic cover and flex the slot to open that side of the plastic cover.
3. Insert the screwdriver into the slot on the other side of the plastic cover and repeat the procedure, and then remove the cover.
4. Insert a new CR2032 lithium coin battery at an angle while observing battery polarity and then press down on the battery.
5. Replace the cover and put the device back to its original position.
6. After restoring a low battery trouble, the system may take up to 5 minutes to clear the trouble signal.
7. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment - Door & window security contact (PG9975)

[img src="//images.ctfassets.net/9mt4r6ro1ay9/5jBTVnkXY9xzyrnp7aw2GH/f2e87ed86888fcda6dd263229d7720f5/i_pg9303.jpg" alt="ALT TEXT." max-width="250"]

Before you start, you will need:

- A new CR2450 battery (purchased online or through a local retailer)
- Small flat-head screwdriver

To replace the batteries for your Door & window security contact (PG9303), please follow the instructions below:

1. Make sure the system is disarmed.
2. Remove the cover of the sensor using a coin.
3. Wedge a flat head screwdriver under the battery.
4. Twist the screwdriver using the base as a lever to remove the battery.
5. Insert a new CR2450 lithium coin battery at an angle with the positive (+) side facing up. Press down on the battery until it fits into place.
6. Replace the cover and put the device back to its original position.
7. After restoring a low battery trouble, the system may take up to 5 minutes to clear the trouble signal.
8. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Door & window security contact (PG9303)

[img src="//images.ctfassets.net/9mt4r6ro1ay9/7JTeI31pI1GyHoK6gtqEA/86f1804abb963965290c236a6b3bc3f5/Door___Window_Sensor.png" alt="Door & window security contact (PG9945)." max-width="260"]

Before you start, you will need:

- A new CR123A battery (purchased online or through a local retailer)
- Small flat-head screwdriver

To replace the batteries for your Door & window security contact (PG9945), please follow the instructions below:

1. Make sure the system is disarmed.
2. Insert a flat-edged screwdriver into the slot and push upward to remove cover.
3. Remove the screw and separate the cover from the base.
4. Remove the former battery and replace with new CR123A battery in the device. Make sure to pay close attention to the polarity when installing the new battery.
5. Connect the sensor wire to the terminal block.
6. After restoring a low battery trouble, the system may take up to 5 minutes to clear the trouble signal.
7. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Door & window security contact (PG9945)

[img src="//images.ctfassets.net/9mt4r6ro1ay9/4xJ5AReeLVl6vdpJUby5WX/9d392945bbbdd2c513064b15d136755d/Glass-break_detector_.png" alt="Glass-break detector." max-width="250"]

Before you start, you will need:

- A new CR123A Battery (purchased online or through a local retailer)

To replace the batteries for your Glass-break detector, please follow the instructions below:

1. Make sure the system is disarmed and remove the device from its original position.
2. Press in the snap and separate the cover from the base.
3. Remove the former battery and replace with a new CR123A battery into the battery clips. Make sure to pay close attention to the polarity when installing the new battery.
4. Replace the cover and put the device back to its original position.
5. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Glass-break detector

[img src="//images.ctfassets.net/9mt4r6ro1ay9/41tZ1I5U1hxbR8b9BMgd5z/74f21dc81177f863bad79ec83676f72f/Wireless_flood_detector.png" alt="Wireless flood detector." max-width="330"]

[youtube:id:aAmgkvTCZH4]

Before you start, you will need:

- A new CR123A battery (purchased online or through a local retailer)
- Small flat-head screwdriver

To replace the batteries for your Wireless flood detector, please follow the instructions below:

1. Make sure the system is disarmed and remove the device from its original position.
2. Insert a flat-edged screwdriver into the slot and push upward to remove the cover.
3. Remove the screw and separate the cover from the base.
4. Remove the former battery and replace with new CR123A battery in the device. Make sure to pay close attention to the polarity when installing the new battery.
5. Replace the cover and put the device back to its original position.
6. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Wireless flood detector

[img src="//images.ctfassets.net/9mt4r6ro1ay9/0jF1cg4zOtxsBa06B7uUj/0fc5b1bccfed4ec497eeb8b46f419216/Wireless_motion_detector_.png" alt="Wireless motion detector." max-width="250"]

Before you start, you will need:

- A new CR123A battery (purchased online or through a local retailer)
- Small Phillips screwdriver, if needed

To replace the batteries for your Wireless motion detector, please follow the instructions below:

1. Make sure the system is disarmed and remove the device from its original position.
2. If a screw was used to secure the sensor during the installation, use a Phillips screwdriver to loosen the screw at the bottom of the Motion Sensor by turning it counter clockwise. If not, proceed to the next step.
3. Press the bottom of the cover and separate the cover from the base of the device.
4. Remove the former battery replace with new CR123A battery in the device.
5. Replace the cover and put the device back to its original position.
6. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Wireless motion detector

[img src="//images.ctfassets.net/9mt4r6ro1ay9/4CQc9EMAP6x5bJsMdYy6rT/38032e12cc01eaa43ae78011a81f472f/Wireless_smoke___heat_alarm.png" alt="Wireless smoke and heat alarm." max-width="250"]

[youtube:id:aO2fDBlrKwc]

Before you start, you will need:

- Three new AAA batteries (purchased online or through a local retailer)

To replace the batteries for your Wireless smoke & heat alarm, please follow the instructions below:

1. Make sure the system is disarmed and on "test" when replacing the batteries for your device. To put your service on test, please [contact us](https://www.telus.com/en/business/support/contact-us).
2. Remove the sensor from its mounting base by twisting it counter-clockwise.
3. Remove the original batteries.
4. To ensure proper power-down sequence, wait a minimum of 20 seconds before installing the new batteries.
5. Install 3 new AAA batteries in the battery compartment. Pay attention to the polarity diagram inside the compartment. If the batteries are incorrectly inserted, please remove gently with a non-conductive tool and correctly reinsert.
6. Reinstall the sensor onto the mounting base by turning the sensor clockwise until the mating marks align.
7. After the power-up sequence, the green LED should blink about once every 12 seconds to indicate normal operation. If the batteries are not installed correctly, the sensor will not operate and the device will not power up.
8. Do not press the test button as this may cause a false alarm which could result in fees for you. Instead, check on your panel or app to see if the low battery alert has cleared.
9. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Wireless smoke & heat alarm

[img src="//images.ctfassets.net/9mt4r6ro1ay9/4CDRExnTvxGZ87QFjzn8Ia/947003d98881ba03eedb35cba48006d9/Carbon_monoxide_alarm_.png" alt="Carbon monoxide detector (PG9933)." max-width="250"]

[youtube:id:hdNaQDynTzI]

Before you start, you will need:

- A new CR123A 3V lithium battery (purchased online or through a local retailer)

To replace the batteries for your Carbon Monoxide (CO) Detector, please follow the instructions below:

1. Make sure the system is disarmed and on "test" when replacing the batteries for your device. To put your service on “test”, please [contact us](https://www.telus.com/en/business/support/contact-us).
2. Remove the detector from its mounting base by twisting the detector counter-clockwise.
3. Remove the original batteries.
4. To ensure proper power-down sequence, wait a minimum of 20 seconds before installing the new batteries.
5. Install a new 3V CR123A lithium battery in the battery compartment. Pay attention to the polarity diagram inside the compartment. If the batteries are incorrectly inserted, please remove gently with a non-conductive tool and correctly reinsert.
6. Reinstall the detector onto the mounting base by turning the detector clockwise.
7. After the power-up sequence, the green LED should blink about once every 12 seconds to indicate normal operation. If the batteries are not installed correctly, the detector will not operate and the device will not power up.
8. Do not press the test button as this may cause a false alarm which could result in fees for you. Instead, check on your panel or app to see if the low battery alert has cleared.
9. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Carbon monoxide detector (PG9933)

[img src="//images.ctfassets.net/9mt4r6ro1ay9/H7lqDeEBAeCgvuPw3JqTt/3ca01c4e2e06407785ab5321b39b6254/Carbon_Monoxide_detector.png" alt="Carbon monoxide detector (PG9913)." max-width="250"]

Before you start, you will need:

- A new 9V battery battery (purchased online or through a local retailer)

To replace the batteries for your Carbon Monoxide (CO) Detector (PG9913), please follow the instructions below:

1. Make sure the system is disarmed and on "test" when replacing the batteries for your device. To put your service on “test”, please [contact us](https://www.telus.com/fr/business/support/contact-us).
2. Separate the detector from the bracket by rotating the detector counter-clockwise.
3. Open the battery cover and connect the 9V battery to its terminals without the insulator. Verify proper polarity.
4. After restoring a low battery trouble, the system may take up to 5 minutes to clear the trouble signal.
5. Do not press the test button as this may cause a false alarm which could result in fees for you. Instead, check on your panel or app to see if the low battery alert has cleared.
6. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Carbon monoxide detector (PG9913)

[img src="//images.ctfassets.net/9mt4r6ro1ay9/2shy15jw1xlOWM26mDs2oH/51ae294969b6f05ef0bd6628c5bf54f8/2.png" alt="Control panel." max-width="270"]

To replace the battery on your IQ2/IQ4 Control Panel, please [contact us](https://www.telus.com/en/support/contact-us#phone).

Qolsys equipment / Control panel

[img src="//images.ctfassets.net/9mt4r6ro1ay9/RAttLx3YoUdtEITgaOpSR/d10b789aa0df567cbb40539afb82a921/Panic_button_remote.png" alt="Panic button remote." max-width="250"]

Before you start, you will need:

- A new CR2032 battery (purchased online or through a local retailer)

1. To replace the battery, insert a coin into the slot on the bottom of the unit and twist it open.
    - __Note__: Make sure the elastic pad within the cover remains in place. Put it back in place if it falls off.
2. Extract the old battery from its holder and replace it with a recommended new CR2032 battery. Ensure that the plus side of the battery faces up, attaining correct polarity.
3. Test the device by pressing the button. The LED indicator should light.
4. Replace the covers securely, verifying that the cover snaps shut.
5. Dispose of the used battery by contacting your local battery recycling programs.

Qolsys equipment / Panic button remote

Qolsys equipment

Change the batteries in your Qolsys equipment / Child Article Config

Main-Security-Control-Panel

Qolsys equipment Swiftype Title

Learn how to change the batteries in your Qolsys equipment, including wireless motion detector, glass break detector and other SmartHome Security devices. 

Qolsys equipment Swiftype Description

Qolsys equipment / SEO

Learn how to change the batteries in your Qolsys equipment, including wireless motion detector, glass break detector and other Secure Business devices. 

Qolsys equipment battery replacement | Support | TELUS Business

Change the batteries in your Qolsys equipment

<img src="//images.ctfassets.net/9mt4r6ro1ay9/5fgiE4uB22nC4G6ToUax44/7cfee1eeeb9fc0dfe36593b5973864ab/Smart_Garage_Door_Controller.png" width="300" height="auto" alt="Smart Garage Door Controller">

1. To open the case, twist a small screwdriver in case slot.
2. Insert a new CR2032 lithium coin battery into the transmitter.
3. Snap the sensor onto the mounting plate.
4. Dispose the used batteries by contacting your local battery recycling programs.


Other devices / Garage door controller tilt sensor

<img src="//images.ctfassets.net/9mt4r6ro1ay9/5n3HT1CrshxK87vDouuxar/efe9fe6e3c754f8ef4a184d483d645c7/Smart_thermostat.png" width="359" height="auto" alt="Smart thermostat">

1. Open the front panel (the front cover should come off).
2. Insert four new AA batteries.
3. Close the front panel.
4. Test whether the replacement is successful by checking the new battery percentage of the thermostat on the panel.
5. Dispose the used batteries by contacting your local battery recycling programs.

Learn how to replace the battery of your TELUS Secure Business smart thermostat from your phone. Do it yourself by watching this brief video:

[youtube:id:0qoYbhEEidA]

Other devices / Smart thermostat

<img src="//images.ctfassets.net/9mt4r6ro1ay9/6L1g4KiRojZC4XlPBWshd3/5c92eb8eb4582442e956b301e0e03a0f/Smart_door_lock.png" width="316" height="auto" alt="Smart door lock">

1. Use a Phillips Screwdriver to loosen the three screws (two located on the side and one at the bottom of the device) and remove the cover from the door lock.
2. Slide-out the battery pack from the interior assembly.
3. Insert 4 new AA batteries into the battery pack.
4. Return the battery pack into the interior assembly.
5. Replace the cover and tighten the screws.
6. Dispose the used batteries by contacting your local battery recycling programs.

Learn how to replace the battery of your TELUS Secure Business smart door lock from your phone. Do it yourself by watching this brief video:

[youtube:id:DUjjGnWZChs]

Other devices / Smart door lock

<img src="//images.ctfassets.net/9mt4r6ro1ay9/3V648AdD6XKvnWt6Q9SubM/61cd971301a95b5ff1bed5a901892b5f/Honeywell_motion_detector.png" width="200" height="auto" alt="Honeywell motion detector">

1. If necessary, loosen the captive lock screw and lift the cover off.
2. Remove 4 screws that secure the detector to the back box.
3. Observe the proper polarity and replace the batteries with a new CR123A battery 
4. After restoring a low battery trouble, the system may take up to 5 minutes to clear the trouble signal
5. Dispose of the used battery by contacting your local battery recycling programs.


Other devices / Honeywell motion detector 

<img src="//images.ctfassets.net/9mt4r6ro1ay9/6AdkwU7PuiEguex0V3M2WJ/acab8c3d75ec3ead6db37de878aa546a/Honeywell_smoke_detector.png" width="300" height="auto" alt="Honeywell smoke detector">

1. Remove the smoke alarm from its mounting base by twisting the smoke alarm counterclockwise. Remove the battery
2. To ensure proper power-down sequence, wait a minimum of 20 seconds before installing a new battery
3. Install a new 3-volt CR123A Lithium battery in the battery compartment
4. Reinstall the smoke alarm onto the mounting base by turning the smoke alarm clockwise
5. Test the smoke alarm. The green LED should blink about once every 10 seconds to indicate normal operation. If the battery is not installed correctly, the smoke alarm will not operate and the battery may be damaged. If the smoke alarm does not appear to be sending a signal during any of the tests, check for correct battery installation and for a fully charged battery
6. Dispose of the used battery by contacting your local battery recycling programs.


Other devices / Honeywell smoke detector

Other devices

Change battery of Smart door lock and other devices

Other devices Swiftype Title

Learn how to change the batteries in your SmartHome Security devices, such as smart door lock, smart thermostat and garage door controller. 

Other devices / SEO

Learn how to change the batteries in your Secure Business devices, such as smart door lock, smart thermostat and garage door controller.

Change battery of Smart door lock and other devices | Support | TELUS Business

Change the batteries in your TELUS Secure Business devices

Change the batteries in your Secure Business devices / SEO

Learn how to change the batteries in your Secure Business devices, including smart door lock, smart thermostat and garage door controller.